+90 532 651 08 79 
+90 507 215 66 82 
+90 507 215 66 82 
Technicial Specifications
| Brush Engine: | 220 / 550 (Volt / Watt) |
| Vacuum Engine: | 220/1200 (Volt/Watt) |
| Clean / Dirty Water Tank: | 61/65 L |
| Brush Piece/ Diameter: | 1/42cm |
| Brushing cycle : | 170 RPM |
| Cleaning Width : | 800 mm |
| Max. Performance: | 2500 m2/hour |
General features
It does not clean the dirt by spreading it on the surface like a mat. It provides effective cleaning by vacuuming the dirty water on the floor during brushing.
It can be used on all floors such as marble, tile stone, granite, epoxy. It does not damage the floor.
45 lt. per hour with min. 2500 m⊃2; area is cleaned.
The amount of water can be adjusted according to the soiling rate of the floor.
It does not require the use of special chemicals for floor cleaning, it is sufficient to use non-foaming surface cleaner chemicals.
The amount of chemical use is very small, equal to 1/10 of the amount of chemicals used in mop cleaning.
Thanks to its electrical feature, it can be used 24 hours a day, 7 days a week.
It is used in schools, factories, shopping malls, hotels and markets.
Thanks to the multi-wheel system, it can be managed even with one hand.
Thanks to its adjustable rear suction apparatus, it fits perfectly on all surfaces and does not leave water.
Domestic production, extensive service network, affordable spare parts
About Product
E7501 floor scrubber, the most powerful and high-capacity version of floor cleaning machine, removes dirt and dust from all floors with its uninterrupted power, with a brush diameter of 42 cm and a rotation speed of 170 RPM. The floor cleaning machine E7501 will allow you to move around the length of the cable, since it is electric with a cable. For these reasons, while it is the exact machine sought in some factories, it may cause difficulties in some areas. In such cases, the battery-powered version can be preferred to avoid potential problems. In factories where occupational safety is highly controlled, a battery powered floor cleaning machine is preferred instead of an electric floor washing machine in order to prevent the situations that can be created by the cable. With the water given to the floors washed with E7501 and the detergent with antifoam to clean, the dirt on the floor is softened. It is removed with a brush and vacuumed with the 80 cm wiper rubber suction apparatus at the back of the machine. It is designed to absorb up to 90% of moisture content. 10% moisture content clings to the micron pores of the floor. The remaining moisture will be removed naturally. It will dry many times faster than release irrigation and other ground cleaning methods. The walk behind / battery powered model E7501 has the highest capacity and performance of any other floor washing and cleaning machine available on the market. Arrangements can be made for performance increase in special projects. There are models designed for use in areas requiring lower energy consumption and lower performance of floor cleaning machines. You can find our other models in the similar products section below.
User Guide
The usage areas of floor scrubbers are as follows;
Laminate and wood materials can be used on all floor types except tiled floors. The main reason why it cannot be used on laminate floors is that it does wet cleaning. Laminate floors are not suitable for use as they have an inflatable structure when they absorb water. Except those; It is suitable for use on concrete floors, marble floors, granite floors, ceramic and tile floors.
Take the brush (diameter 43 cm) that we have supplied with the machine.
Have another person lift ten of the machine by pressing down on the handle with both hands.
Bring the brush in your hand to the bearing in front of the motor. Make sure that the brush is attached by approaching it parallel to the gaps in the brush and turning the brush to the left.
Then lower the front of the vending machine to the ground.
Open the lid of the blue clean water tank and add enough water and detergent.
As a detergent, you should definitely prefer detergents and shampoos that do not foam.
Charge your machine before starting to work. Press the pedal at the bottom right behind the machine with your right foot and push it to the right.
The pedal will go up. In this way, ensure that the brush descends (touches the ground).
Open the water valve located at the bottom left of the back of the machine according to the pollution and type of the ground.
Start the brush by pressing the brush motor button on the machine (on the panel) and take the machine to the place where you will wash it.
Wash it this way.
When you want to do both washing and vacuuming, while the washing process is being performed, pull the apparatus lifting lever located in the upper middle of the back of the machine down from its place and make the apparatus go down and press the vacuum motor button. In this way, while washing, vacuuming is done at the same time.
When you are finished cleaning, turn off the water valve and absorb the remaining water on the floor. Then turn off the vacuum motor switch (red button).
Turn off the brush motor switch (green button) when the brush is in the down position (on the ground).
Press down on the brush lift pedal with your left foot so that the brush stays in the up position (in the air).
Then park the machine in a place where it will not be damaged or damaged.
FAQ
FAQ alanına henüz içerik girişi yapılmadı.